MATERIAL SAFETY DATA SHEET

DATE PREPARED: MAR 07,2005

NAME OF PREPARER: LUCY ZHOU

MSDS NO.: ZYSG2005001 Production License No.: XK06-225-00903

ISO9001-2000 qualified partner Certificate No.: 05403Q11155R0S

 

SECTION 1. CHEMICAL PRODUCT AND COMPANY INFORMATION

 

PRODUCT NAME

Mixed abrasives resin boned grinding wheel

Resin Bonded Flute Grinding Wheel

Resin Bonded Split Point Grinding Wheel

Resin Bonded Point Grinding Wheel

Resin Bonded Clearance Grinding Wheel

Resin Bonded Tap Square Grinding Wheel

TRADE NAME

ZHONG YANG WHEEL

MANUFACTURER

ZHONGYANG GRINDING WHEELS INDUSTRIAL CO.,LTD.

Aizhuang Economic Development Zone, Xuchang, Henan, P.R. China 461143

Tel: 86-374-574-1116 Fax: 86-374-574-1716

 

SECTION 2. COMPOSITION/INFORMATION ON INGREDIENTS

 

SUBSTANCE DESCRIPTION PERCENT CAS#

Aluminum Oxide, Non-fibrous 50.00-55.00 1344-28-1

Silicon Carbide 40.00-45.00 409-21-2

Cured Phenol/Formaldehyde Resin 3.00-6.00 9003-35-4

Fiberglass **N/A

Calcium Oxide 1.00-3.00 1305-78-8


Carbon Black 0.10-0.60 1333-86-4

Other

Not Applicable

 

SECTION 3. HAZARDS IDENTIFICATION

 

INHALATION ACUTE EXPOSURE EFFECTS

DUST AND SMOKE while grinding may be slightly irritating to eyes and respiratory tract at
high concentrations.

Inhalation Chronic Exposure Effects

For products containing phenol/formaldehyde resin, dust generated from intended use may
contain trace amounts of phenol and formaldehyde which under excessive exposure may
cause skin sensitization and airway obstruction.

 

SECTION 4. FIRST AID MEASURES

INHALATION

Remove to fresh air. If breathing has stopped, give artificial respiration. Get medical
attention immediately.

SKIN CONTACT

Wash affected areas with soap and water. Obtain medical assistance.

EYE CONTACT

Wash with large amounts of water. Obtain first aid and medical assistance, if needed.

INGESTION

Call poison control center, hospital emergency room or physician immediately.

 

SECTION 5. FIRE AND EXPLOSION HAZARD DATA

 

Flash Point(method used): **N/A

Flammable Limits: LEL: **N/A UEL: **N/A

Extinguishing Media: Water spray, CO2

Special Fire Fighting Procedures: Fire fighters should wear self-contained breathing
apparatus to avoid inhalation of smoke or vapors.

Unusual Fire and Explosion Hazards: **N/A

 

SECTION 6. HANDLING AND STORAGE

 

HANDLING

Always HANDLE AND STORE wheels in a CAREFUL manner.

Always VISUALLY INSPECT all wheels before mounting.

Always CHECK MACHINE SPEED against the established maximum safe operating speed
MARKED ON THE WHEEL.

Always CHECK MOUNTING FLANGES for equal and correct diameter.

Always be sure WORK REST is properly adjusted.

Always USE A SAFETY GUARD covering at least one-half of the grinding wheel.


Always allow NEWLY MOUNTED WHEELS TO run at operating speed, with guard in place,
for at least on minute before grinding.

Always TURN OFF COOLANT before stopping wheel to avoid creating an out-of-balance
wheel.

 

SECTION 7. STABILITY AND REACTIVITY

 

Stability: Stable

Hazardous Polymerization: Will not occur

INCOMPATIBILITIES

Avoid acids of all types with a PH < 4.0.

DECOMPOSITION

In use, dust and decomposing odors may be generated. In most cases, the material
removed from the workpiece will be significantly greater than the grinding wheel
components. Coolants may produce other decomposition products.

For products containing Phenol and Formaldehyde resin, thermal decomposition may
produce trace amounts of phenol and formaldehyde.

For products containing inorganic fluorides, thermal decomposition may produce trace
amounts of fluorides.

 

SECTION 8. TRANSPORT INFORMATION

 

This product is not hazardous as defined by the department of Transportation.

This product is “Not Regulated” under the Transportation of Dangerous Goods Act.

 

SECTION 9. DISPOSAL CONSIDERATION

 

WASTE DISPOSAL

Use standard landfill methods consistent with applicable Federal, State, Provincial and local
laws.

Products with listed fluorides may have slightly soluble fluoride swarf.

**N/A = Not Applicable.

Download MSDS PDF File: